1.2 1.5 不允許臺歷裝訂機 掛歷裝訂機 日歷裝訂機 筆記本裝訂機機器運轉時，維護運動零部件和靠近運動零部件的其他零部件。 It is not permissible to maintain moving parts and other parts near moving parts while the machine is running.
1.6 大面積保養或修理時，必須按下“停止”自鎖按鈕，切斷所以電源、氣源。Large area maintenance or repair, you must press the "stop" self-locking button, cut off the power supply, gas source.
1.7 在進行調整、保養和修理工作時，不得使用不適當?shù)墓ぞ摺９ぷ魍戤吅蟊仨毲謇頇z查機器上的工具和其他雜物，以免發生故障。 Undue tools should not be used for adjustment, maintenance and repair work. After the work must be cleaned to check the tools and other debris on the machine, so as to avoid failure.
1.8 在重新啟動機器前，應檢查所有安全設施是否處在正常位置，是否緊定，注意機器周圍的其他人員是否處在安全的位置。 Before restarting the machine, check that all safety devices are in their normal b, are they tightened, and that the rest of the machine is in a safe place.
1.9 保持機器和周圍環境的清潔，及時清除掉落在地板上的油污，清理工作區的工具、抹布及碎紙廢料等。 Keep the machine and the surrounding environment clean, remove the oil on the floor in a timely manner, clean up the work area of the tools, rags and shredded scrap.
1.10 及時維護、更換已失效和損壞的裝置，及時報告機器發生的問題。Timely maintenance, replacement of failure and damage to the device, the timely report of the machine problems.
2．收放物料裝置的調整 Adjust the feed and receive belt
2.1 臺歷裝訂機 掛歷裝訂機 日歷裝訂機 筆記本裝訂機上料裝置的調整 Adjust the feed belt
該工位可根據產品的寬窄來調節輸送料道的寬度，參考（圖九）松開護罩1的固定螺絲123，然后根據產品的需要調整料道的寬窄。The b of the station can be adjusted according to the b of the product to adjust the b of the conveyor material, refer to (Picture 9) to release the cover screw 1 123, and then adjust the b of the material according to the needs of the material.
收料裝置的調整(參考圖三) Adjust the receive belt (Picture 3)
該工位主要是配合主機完成收料工作，可根據主機的裝訂速度自動調整線體的每次位移. The station is mainly with the host to complete the receipt work, according to the host's binding speed automatically adjust the line of each displacement.
3. 臺歷裝訂機 掛歷裝訂機 日歷裝訂機 筆記本裝訂機推刀調試 Test push knife
根據產品大小的需要，可通過調節推刀組的固定螺絲的安裝位置來調節T的寬度（見圖十）Depending on the size of the product, the b of the T can be adjusted by adjusting the mounting b of the setscrews' fixing screws (Picture 10)
河南省
鄭州市 南陽市 新鄉市 安陽市 洛陽市 信陽市 平頂山市 周口市 商丘市 開封市 焦作市 駐馬店市 濮陽市 三門峽市 漯河市 許昌市 鶴壁市 濟源市
臺歷裝訂機 掛歷裝訂機 日歷裝訂機 筆記本裝訂機