人妻综合网,欧美一级二级三级视频,日韩精品无码波多野结衣,无码国产精品一区二区高潮

產品簡介
DP-F31-LIN
DP-F31-LIN
產品價格:¥1000
上架日期:2017-09-26 20:36:10
產地:美國OMEGA
發貨地:深圳
供應數量:不限
最少起訂:1件
瀏覽量:63
資料下載:暫無資料下載
其他下載:暫無相關下載
詳細說明

    DP-F31-LIN詳細介紹


    DP-F31-LIN

    批量控制器,帶兩級閥控制
    DPF-310 Series

    Start/Stop Buttons
    Separate 8-Digit KFactors for Rate and Total
    Pulse or Analog Input Models Available
    Displays Rate, Total and Grand Total
    Security Lockout
    2 Set Points for 2-Stage Valve Control
    NEMA 4X (IP65) Front Panel

    產品描述
    Featuring 8 digits of bright, 14 mm (0.55"), alphanumeric display, the DPF-310 Series can accept up to 20,000 pulses per second of digital count. The analog b version accepts 4 to 20 mA signal and it uses a highly linear integrator (V to F converter) to generate 0 to 10 kHz digital pulses. The standard unit has 2 separate, 8-digit, floating decimal, “K” factors to convert the bs to meaningful total and rate data. An optional 16-point K-factor can linearize flow from non-linear meter outputs. The user, with the push of a button, can toggle back and forth to view the total of the batch, the rate of flow or the grand total of flow.

    The DPF-310 Series may be thought of as two separate counters and a ratemeter. The “batching” counter counts to prewarn and preset numbers entered by the user and enables separate control outputs. The “totalizing” counter gives a cumulative reading or grand total. Finally, the ratemeter counts the number of pulses per second and, with its scaling feature, can provide gallons per minute or any other rate measurement without the totalizer losing counts.

    At any time, the user may view the total, the grand total or the rate while never interrupting the counting process. Setup is done through the front panel and the menu driven software in the unit. Start-stop control can be activated via the front panel buttons or remote bs (on some models). The unit operates from either 110 Vac/12 to 27 Vdc, or optional 220 Vac/12 to 27 Vdc. If AC power is used, 2 built-in regulated 12 Vdc @ 100 mA power supplies are offered. They can be connected to provide +12 Vdc and -12 Vdc or +24 Vdc to drive external devices.

    CMOS logic is used to provide high noise immunity and low power consumption with EEPROM to hold data a minimum of 10 years if power is interrupted.

    SPECIFICATIONS
    Display: 8-digit, 14 mm (0.55") high, 15 segment, red orange, LED
    Input Power (Internally Fused):
    110 Vac ±15% or 12 to 27 Vdc
    220 Vac ±15% or 12 to 27 Vdc (“-220V” Vac option)
    Current: Maximum 280 mA dc or 5.3 VA at rated ac voltage
    Output Power (On AC Powered Units Only): 12 Vdc @ 100 mA. Separate isolated 12 Vdc @ 100 mA to allow 12 Vdc or 24 Vdc regulated ±5% worst case (DC outputs are supplied with re-settable fuses)
    Temperature:
    Operating: 0 to 54°C (32 to 130°F)
    Storage: -40 to 93°C (-40 to 200°F)
    Humidity: 0 to 90% non-condensing
    Approvals: CE approved
    Memory: EEPROM stores all program and total data for minimum of 10 years if power is lost
    Pulse Inputs (DPF-311): Standard, high impedance pulse b
    Low: Open or 0 to 1 Vdc
    High: 3 to 30 Vdc, 10 kù impedance, 20 kHz max b speed (min on/off 25 msec) or field changeable to: 4.7 kù b pull up resistors to 5 Vdc on b for pulsing with contact to ground or NPN open collector transistor
    Analog Inputs (DPF-312): The current loop b is converted to a highly linear 0 to 10 kHz frequency. This frequency can then be scaled by the 8-digit K-factors to total or display rate in separate engineering units
    Accuracy Over Full Temperature Range
    Zero Error: 0.175% full scale max
    Overall Error: 0.5% full scale max
    DPF-312: 4 to 20 mA, 250 Ω impedance
    Front Push Button Reset: “CLR” resets displayed number and control output
    Remote Start and Stop/Reset Inputs (Not available on DPF-312-A or models with the “-LIN” option): A 4 to 30 Vdc positive pulse will activate these bs. Pin 10 is the START b and when activated, the unit will “start”. Pin 5 is the STOP/RESET b. When activated, the unit will “stop” (if unit is started and the batch is not complete). When the unit is stopped or the batch is complete, activating this b will reset the total. If pin 5 is held high (4 to 30 Vdc), the display will flash “STOPPED” and any start bs will be inhibited. Stop always over-rides start b.
    Control Outputs, SPDT Relay Version: 10 A 120/240 Vac or 28 Vdc (resistive)
    Analog Output (“A” Models) Current Outputs: A sinking driver generates a corresponding linear current through the external devices, updating with each update of the rate. Accuracy is ±0.5% FS worst case. Compliance voltage must be 3 to 24 Vdc, non inductive. (The DPF-310 Series can provide the DC source as long as the drop across all devices being driven does not exceed 21V)
    Security: The DPF-310 Series has a missing pulse detector. The user selects the amount of time (1 to 99 sec) that the unit will “wait” for b pulses. If the unit doesn't receive pulses within the selected time, the unit displays “SECURITY” and both relays drop out. (00 disables the security feature; entering the lockout code returns the unit to the run mode)
    Presets: The user may enter two numbers to set up the batch totalizer, preset and prewarn. The prewarn is a number set a certain number of counts before the preset number. For instance, you may want one hundred gallons in a particular batch. You may also want a valve to close and slow down flow 25 gallons before the end. Your preset is 100, your prewarn is 25. When the start is activated, the relays energize simultaneously to start flow. When the totalizer reaches 75, the prewarn relay drops out. When the totalizer reaches 100 the preset relay drops out. The preset values can be viewed or changed via the menu (when stopped).
    K-Factor: In the standard unit a fixed K-factor is used to convert the b pulses or frequency generated internally by the analog b to engineering units. The 8-digit K-factor dividers, with decimal keyed into any b, allow easy direct entry of any K-factor greater than 0.0001 to 99,999,999. Separate K-factors may be entered for the total and rate section. Thus, you may batch and total in gallons and display rate in liters per hour. The maximum factored count speed is 20,000 Hz. The maximum factored rate is 7-digits.
    16-Point Linearization ("-LIN" option): This variable K-factor option makes flow systems more accurate and often extends their usable range by allowing users to dial in different K-factors for different flow rates. It works with either pulse b or standard analog current loop. It is recommended for flow meters whose K-factors change with different rates of flow. This option can also be used to display static volume in irregular shaped vessels by interfacing level or pressure transducers to the analog b. From 3 to 16 points of frequency from 0 to 10,000 Hz and Kfactors greater than 0.0001 to 999,999 are dialed in at set up. The 16 point linearization option uses 8 digit floating math to interpolate between settings. Rate per second, per minute or per hour programmability eliminates the need to calculate separate K-factors for total and rate.
    Totalizer: Each of the total and grand total counters have 8 digits. In the setup mode choose "R0" (reset to zero) for count up operation or "SP" (set to preset) for count down operation. While viewing the total the display can be made to flash the grand total by pressing "ENT". Activating "CLR" while the grand total is flashing, resets the grand total counter.
    Ratemeter: Accurate to 51.2 digits (1 display digit). The rate meter can be programmed to accept almost any number of pulses per unit of measurement, sample from 2 to 24 seconds maximum, and autorange up to 6 digits of significant inbation. The rate meter with a "K" factor of 1 displays the rate of pulses per second. Simply dial in the proper "K" factor to display in minutes, hours or other units of measurement. (See 16-Point Linearization above) Press the "C" button while the unit is displaying the batch to display the rate; "R" is displayed on the left side of the display.
    Weight: This feature is used to provide a weighted averaging of the rate data being received. Higher settings provide more averaging for a more stable display, derived from the equation: (Old Data x "Weight") + New Data ("Weight" +1)
    Lockout: Unauthorized front panel changes can be prevented by entering a user selected four digit code.
     

    注: Comes complete with operator’s manual.

    產品編號  產品描述

    DPF-311  Batch controller, pulse b

    DPF-311-A  Batch controller, pulse b, analog output

    DPF-312  Batch controller, analog b

    DPF-312-A  Batch controller, analog b , analog output



     DP-F31-LIN


    DP-F31-LIN 相關產品

    DP-F31-LIN 技術文章

在線詢盤/留言
  • 免責聲明:以上所展示的信息由企業自行提供,內容的真實性、準確性和合法性由發布企業負責,本網對此不承擔任何保證責任。我們?cè)瓌t 上建議您選擇本網高級會員或VIP會員。
    企業信息
    深圳市鑫博恒業科技有限公司
    會員級別:家家通數字營銷版
    ------------ 聯系方式 ------------
    聯系人:李經理(小姐)
    聯系電話:0755-82736276
    聯系手機:18924605141
    傳真號碼:0755-83041664
    企業郵箱:235521054@qq.com
    網址:
    郵編:518031
    推薦供應
    0571-87774297  
    美女被操网站在线观看| 国产又色又爽又黄的| av色先锋| 狠久久| 婷婷五月丁香综合| 人妻精品| 亚洲AV无码专区国产乱码电影| 欧美激情五月| 婷婷综合在线| 国产精品热久久| 国产色无码精品视频国产| 精品国产精品三级精品| 粉嫩AV无码一区二区三区软件| 99无码熟妇丰满人妻啪啪| 妺妺窝人体色www聚色窝网站| 欧美先锋影音| 麻豆v视a频在线观看| 香蕉久久精品| 欧美国产亚洲精品| 久久久婷婷| √天堂8在线网| 成人羞羞国产免费| 久久亚洲精品国产精品黑人 | 日韩精品无码成人专区真希| 精品无码999| 欧美色精品| 日韩人妻无码一区二区三区色欲 | 中文AV网站| 日韩v在线观看| 亚洲国产精品久久亚州精品1区| 久久八| 久久国产毛片| 无码人妻精品一区二区蜜桃网站| 肉大捧一进一出好爽mba| 丁香五月天视频| 亚洲高潮影院| 久久精品无码一区| 思思热在线视频精品| 少妇影院yy111111| 天堂8在线中文在线| 99久久99九九99九九九|