CYC-CAL-325-CERT詳細介紹
CYC-CAL-325-CERT
超導和低溫溫度測量 ? CYC320系列自動調諧控制器 ? CYC325
雙通道自整定溫度控制器
CYC325
Operates Down to 1.2 K with Appropriate Sensors
2 Sensor Inputs
Supports Diode, RTD, and Thermocouple Sensors
Sensor Excitation (Current Reversal Eliminates Thermal EMF Errors for Resistance Sensors)
2 Autotuning Control Loops: 25 and 2 W Max
Control Loop 2: Variable Vdc source from 0 to 10 V Max
IEEE-488 and RS232C Interfaces
產品描述
The CY325 Series dual-channel temperature controller is capable of supporting nearly any diode, RTD, or thermocouple temperature sensor. Two independent PID control loops with heater outputs of 25 and 2 W are configured to drive either a 50 or 25 ù load for optimal control flexibility. Designed with ease of use, functionality, and value in mind, the CYC325 Series is ideal for general-purpose laboratory and industrial temperature measurement and control applications.
SPECIFICATIONS
Thermometry
Number of Inputs: 2
Input Configuration: Each b is factory configured for either diode/RTD or thermocouple
Isolation: Sensor bs optically isolated from other circuits but not each other
A/D Resolution: 24-bit
Input Accuracy: Sensor dependent, refer to b specifications table
Measurement Resolution: Sensor dependent, refer to b specifications table
Max Update Rate: 10 rdg/s on each b (except 5 rdg/s on b A when configured as thermocouple)
Filter: Averages 2 to 64 b readings
Sensor Input Configuration Diode/RTD:
Measurement Type: 4-lead differential
Excitation: Constant current with current reversal for RTDs
Supported Sensors: Diodes, silicon, GaAlAs; RTDs, 100 ΩPlatinum, 1000 Ω Platinum, germanium, carbon-glass, CernoxTM, and RoxTM
Standard Curves: CY7 and CY670, PT-100, PT-1000, RX-102A, RX-202A
Input Connector: 6-pin DIN
Thermocouple:
Measurement: 2-lead, room temperature, compensated
Excitation: N/A
Supported Sensors: Most thermocouple types
Standard Curves: Type E, Type K, TypeT, AuFe 0.07% vs Cr, AuFe 0.03% vs Cr
Input Connector: Ceramic isothermal block
Control
Control Loops: 2
Control Type: Closed loop digital PID with manual heater output or open loop
Tuning: Autotune (1 loop at a time), PID, PID zones
Control Stability: Sensor dependent, see b specification table
PID Control Settings:
Proportional (Gain): 0 to 1000 with 0.1 setting resolution
Integral (Reset): 1 to 1000 (1000/s) with 0.1 setting resolution
Derivative (Rate): 1 to 200% with 1% resolution
Manual Output: 0 to 100% with 0.01% setting resolution
Zone Control: 10 temperature zones with P, I, D, manual heater out, and heater range
Setpoint Ramping: 0.1 K/min to 100 K/min
Safety Limits: Curve temperature, power up heater off, short circuit protection
Front Panel:
Display: 2-line, 20-character, liquid crystal display with 5.5 mm (0.216") character height
Number of Reading Displays: 1 to 4
Display Units: K, °C, V, mV,
Reading Source: Temperature, sensor units
Display Update Rate: 2 rdg/s
Temp Display Resolution: 0.001° from 0 to 99.999°, 0.01° from 100 to 999.99°, 0.1° above 1000°
Sensor Units Display Resolution: Sensor dependent; to 5 digits
Other Displays: Setpoint, heater range, and heater output; user selected
Setpoint Setting Resolution: Same as display resolution (actual resolution is sensor dependent)
Heater Output Display: Numeric display in percent of full scale for power or current
Heater Output Resolution: 1%
Display Annunciators: Control b, remote, autotune
Keypad: 20-key membrane, numeric and specific functions
Front Panel Features: Front panel curve entry, keypad lock-out
Interface
IEEE-488 Interface Features: SH1, AH1, T5, L4, SR1, RL1, PP0, DC1, DT0, C0, E1
Reading Rate: To 10 rdg/s on each b
Software Support: LabVIEWTM driver; consult factory for availability
Serial Interface:
Electrical Format: RS232C
Baud Rates: 9600, 19200, 38400, 57600
Connector: 9-pin D-style, DTE configuration
Reading Rate: To 10 rdg/s, each b
General
Ambient Temperature: 15 to 35 °C (59 to 95oF) at rated accuracy, 5 to 40 °C (41 to 104oF) at reduced accuracy
Power Requirement: Standard 120 Vac, optional 240 Vac, 6%, -10%, 50 or 60 Hz, 85 VA
Dimensions: 89 H x 216 W x 368 mm D (3.5 x 8.5 x 14.5"), half rack
Weight: 4.00 kg (8.82 lb)
Approval: CE mark
Input Specifications
Sensor Temp Coefficient Input Range Excitation Current Display Resolution Measurement Resolution Electronic Accuracy (at 25°C) Electronic Control Stability1
Diode Negative 0 to 2.5 V 10 μA
±0.05%2,3 100 μV 0.4 μV ±80 μV
±0.005%
of rdg ±20 μV
Diode Negative 0 to 7.5 V 10 μA
±0.05%2,3 100 μV 10 μV ±80 μV
±0.001%
of rdg ±40 μV
PTC RTD Positive 0 to 500? 1 mA4 10 m? 2 m? ±0.004?
±0.01%
of rdg ±4 m?
PTC RTD Positive 0 to 5000? 1 mA4 100 m? 20 m? ±0.004?
±0.02%
of rdg ±40 m?
NTC RTD Negative 0 to 7500? 10 μA ±0.05% 100 m? 40 m? ±0.1?
±0.04%
of rdg ±80 m?
Thermocouple Positive ±25 mV N/A 1 μV 0.4 μV ±1 μV
±0.05%
of rdg5 ±0.8 μV
Thermocouple Positive ±50 mV NA 1 μV 20 μV ±1 μV
±0.05%
of rdg5 ±0.8 μV
1 Control stability of the electronics only, in ideal thermal system
2 Current source error has negligible effect on measurement accuracy
3 Diode b excitation can be set to 1 mA
4 Current source error is removed during calibration
5 Accuracy specification does not include errors from room temperature compensation
注: Comes with heater output connector (dual banana jack), sensor b mating connector (6-pin DIN plugs), terminal block (2-pin), power cord and operator’s manual.
產品編號 產品描述
CYC325 2 diode/RTD bs
CYC325-T1 1 diode/RTD, 1 thermocouple b
CYC325-T2 2 thermocouple bs
Accessories
CYC-6201 1 m (3.3' long) IEEE-488 (GPIB) computer interface cable assembly
CYC-CAL-325-CERT Instrument recalibration with certificate, no points
CYC-CAL-325-DATA Instrument recalibration with certificate and data
CYC-RM-1/2 Rack mount kit for mounting one 1/2 rack temperature controller in 482.60 mm (19") rack, 90 mm (3.5") high
CYC-RM-2 Rack mount kit for mounting two 1/2 rack temperature controllers in 482.60 mm (19") rack, 135 mm (5.25") high
CYC-106-009 Heater output connector, dual banana jack
CYC-106-233 6-pin male b connector
CYC-106-735 Terminal block, 2-pin
CYC-CAL-325-CERT
CYC-CAL-325-CERT 相關產品
CYC-CAL-325-CERT 技術文章
