无码一卡二卡三卡四卡,无码国产精品一区二区免费式影视

產品簡介

斯米克S111鈷基1號堆焊焊絲|RCoCr-A鈷基合金焊絲

產品價格：￥電議

上架日期：2020-06-02 10:32:27

產地：本地

發貨地：天津

供應數量：不限

最少起訂：1千克

瀏覽量：215

點擊詢價 QQ洽談

資料下載：暫無資料下載

其他下載：暫無相關下載

詳細說明

斯米克S111鈷基1號堆焊焊絲|RCoCr-A鈷基合金焊絲上海斯米克S111鈷基1號堆焊焊絲|RCoCr-A鈷基合金焊絲
? 標準：
相當AWS RCoCr-A
? 說明：
S111 是連鑄的低碳鈷鉻鎢（司太立）合金堆焊焊絲，是鈷鉻鎢堆焊合金中碳及鎢含量最低，韌性最好的一種。因此能夠承受在冷熱條件下的沖擊，而且產生裂紋的可能性也小。堆焊層具有良好的耐蝕、耐熱、耐磨性能，在 650℃左右的高溫下，亦能保持這些特性。用硬質合金刀具易進行切削加工，金相組織為含鎢、鉻的鈷基固溶體（奧氏體）和固溶體與鉻鎢復合碳化物共晶。
? 用途：
要求在高溫工作時能保持良好的耐磨性及耐腐蝕性，例如堆焊高溫高壓閥門、熱剪切刀刃、熱鍛模等沖擊和加熱交錯地方，可具有良好的性能。
? 焊絲化學成分（%）
C Mn Si Cr W Ni Fe Co
0.9~1.4 ≤1.0 0.4~2.0 26.0~32.0 3.0~6.0 ≤3.0 ≤3.0 余量
? 堆焊金屬常溫硬度：
HRC=40~45
以上化學成分及常溫硬度指堆焊三層以上堆焊金屬。
? 供應規格（mm）
焊絲直徑Φ 3.2 4.0 5.0 6.0
焊絲長度 350；1000
? 注意事項：
1. 用氧- 乙炔碳化焰進行堆焊，焰心與內焰的長度比應保持為1：3。
2. 焊接面的邊角部分一定要加工成圓角。并在清除母材表面的氧化物及油等污物后進行堆焊。
3. 應當根據母材的種類和工件大小，選擇適當?shù)臏囟冗M(jìn)行預熱。
4. 堆焊時，母材只須加熱到呈“出汗”（潤濕）狀態，便可加入焊絲熔滴

Category 類別		Trade-mark 牌號		Specification 規 格		Melting Point 熔點(℃)	Chemical comb 主要成份(%)	Application 用途	Equivalent to AWS 相當AWS
		L103斯米克銀焊條		Wire & rod 絲		885-888	Cu54 Zn Rem.	Brazing of copper, bronze and steel, subjected to low load. 釬焊銅、青銅和鋼等受力不大工件
		L104斯米克銀焊條		Foil 箔		890-930	Cu57 Mn2 Co2 Zn Rem.	Brazing of carbide cutting tool. 釬焊硬質合金刀具
		L201斯米克銀焊條		Cast rod, wire & rod, powder 鑄條、絲、粉		710-800	P7 Cu Rem.	Brazing of copper and copper alloys. 釬焊銅及銅合金	BCuP-2
		L204斯米克銀焊條		Cast rod, wire 鑄條、絲		640-815	P5 Ag15 Cu Rem.	Brazing of copper, copper alloys, silver and molybdenum etc. 釬焊銅及銅合金、銀、鉬等金屬。	BCuP-5
		L205斯米克銀焊條		Cast rod, wire & rod, powder 鑄條、絲、箔		640-800	P6 Ag5 Cu Rem.	Brazing of copper and copper alloys. 釬焊銅及銅合金	BCuP-3
		L207斯米克銀焊條		Cast rod, wire & rod 鑄條、絲		640-770	P7 Ag5 Cu Rem.	Brazing of copper and copper alloys. 釬焊銅及銅合金	BCuP-7
		L209斯米克銀焊條		Cast rod, wire 鑄條、絲		684-710	P7 Ag2 Cu Rem.	Brazing of copper and copper alloys. 釬焊銅及銅合金。	BCuP-6
		L302斯米克銀焊條		Wire & rod 絲		745-775	Ag25 Cu40 Zn Rem.	Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等
		L303斯米克銀焊條		Wire & rod 絲		660-725	Ag45 Cu30 Zn余	Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等	BAg-5
		L303F斯米克銀焊條		Flux coated rod 涂藥絲		660-725	Ag45 Cu30 Zn Rem.	L303 coated with flux, the same application as L303. 外涂釬劑的L303，用途與L303相同	BAg-5
		L304斯米克銀焊條		Foil 箔		690-775	Ag50 Cu34 Zn Rem.	Brazing of copper, copper alloys and steel etc. 釬焊銅及銅合金、鋼等	BAg-6
		L308斯米克銀焊條		Wire & rod 絲		779-780	Ag72 Cu Rem.	Brazing of copper and nickel under vacuum or reducing protective atmosphere. 銅和鎳的真空或還原保護氣氛釬焊	BAg-8
		L312斯米克銀焊條		Wire & rod 絲		595-605		Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等
		L313斯米克銀焊條		Wire & rod 絲		625-635		Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等	BAg-1a
		L321斯米克銀焊條		Wire & rod 絲		615-650		Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等	BAg-7
		L323 斯米克銀焊條		Wire & rod 絲		665-755		Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等
		L325 斯米克銀焊條		Wire & rod 絲		645-685		Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等	BAg-36
		L326 斯米克銀焊條		Wire & rod 絲		650-720		Brazing of copper, copper alloys, steel and stainless steel etc. 釬焊銅及銅合金、鋼及不銹鋼等	BAg-34
		L400 斯米克銀焊條		Cast rod, wire & rod 鑄條、絲		577-582	Si11.5 Al Rem.	Brazing of aluminum and aluminum alloys. 鋁及鋁合金的釬焊	BAlSi-4
		L401斯米克銀焊條		Cast rod 鑄條		525-535	Si5 Cu28 Al Rem.	Brazing of aluminum and aluminum alloys. 鋁及鋁合金的釬焊
		L600 斯米克銀焊條		Wire & rod 絲		183-185	Sn60 Sb≤0.8 Pb Rem.	Soldering of fusible bls and heat-treated part. 易熔金屬及熱處理件的釬焊	60Sn
		L601 斯米克銀焊條		Wire & rod 絲		183-227	Sn18 Sb2 Pb Rem.	Soldering of copper, copper alloys and galvanized iron plain sheet. 銅及銅合金、鍍鋅鐵皮的釬焊。	18Sn
		L602 斯米克銀焊條		Wire & rod 絲		183-256	Sn30 Sb2 Pb Rem.	Soldering of copper, brass, copper alloys and galvanized iron plain sheet. 銅、黃銅、鐵、鍍鋅鐵皮的釬焊	30Sn
		L603 斯米克銀焊條		Wire & rod 絲		183-235	Sn40 Sb2 Pb Rem.	Soldering of copper, copper alloys, steel and zinc parts. 銅及銅合金、鋼、鋅制零件的釬焊	40Sn
		L604 斯米克銀焊條		Wire & rod 絲		183-222	Sn90 Sb≤0.15 Pb Rem.	Soldering of copper and steel for food and medicine field. 食品、醫療所需銅、鋼等金屬的釬焊	90Sn
		L605 斯米克銀焊條		Wire & rod 絲		232-240	Ag5 Sn95	Soldering of copper and steel for electrical and food field. 電器、食品所需銅、鋼等金屬的釬焊
		L608 斯米克銀焊條		Wire & rod 絲		295-305	Sn5.5 Ag2.5 Pb Rem.	Soldering of copper, copper alloys, steel and stainless steel. 銅及銅合金、鋼及不銹鋼的釬焊
		L702 斯米克銀焊條		Powder 粉		970-1000	Cr7 B3 Si4 Ni Rem.	Brazing of stainless steel under vacuum or protective atmosphere. 不銹鋼真空或保護氣氛釬焊	BNi-2
	Trade- Mark 牌號		Equivalent to China Standard 相當國標		Characteristics & application 特性和用途					Equivalent to AWS 相當AWS
	D 667斯米克焊條		EDZCr-B-15		HRc≥48. Resistance to wear, gas corrosion and oxidation. Hardfacing of blast furnace hopper and cracker part. HRc≥48，耐磨、耐氣蝕、抗氧化。堆焊高爐料鐘、破碎機件
	D 802斯米克焊條		EDCoCr-A-03		HRc38-47. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as the edge of thermo-cutter. HRc38-47，耐熱、耐蝕、耐磨。堆焊高溫工件如熱剪切刀刃					ECoCr-A
	D 812斯米克焊條		EDCoCr-B-03		HRc45-50. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as internal-combustion engine valve. HRc45-50，耐熱、耐蝕、耐磨。堆焊高溫工件如內燃機閥					ECoCr-B
	D 822斯米克焊條				HRc≥53. Resistance to Wear and heat, bad shock resistance. Hardfacing of rotating blade wheel of boiler. HRc≥53，耐熱、耐磨，但抗沖擊性差。堆焊鍋爐旋轉葉輪
	D 832斯米克焊條		EDCoCr-C-03		HRc≥50. Wear and heat resistance. Hardfacing of high temperature part such as hot-rolling guided way. HRc≥50，耐熱、耐磨。堆焊高溫工件如熱軋導軌					ECoCr-C
	D 842斯米克焊條		EDCoCr-D-03		HRc28-38. Corrosion and thermo-fatigue resistance, work harding. Hardfacing of hot forging die. HRc28-38，耐蝕、抗熱疲勞，具有加工硬化性。堆焊熱鍛模
	Z 308斯米克焊條		EZNi		Pure nickel, excellent general properties. Used to weld thin cast iron part and repair welding machined surface, such as guided way of machine tool. 純鎳，綜合性能好。鑄鐵薄件及加工面補焊用，如機床導衛					ENi-Cl
	Z 408斯米克焊條		EZNiFe		Iron nickel, high strength and excellent ductility. Repair welding of important gray cast iron and nodular cast iron, such as cylinder cap. 鎳鐵，強度高、塑性好。重要灰鑄鐵及球鐵焊補用，如汽缸蓋					ENiFe-Cl
	Z 508斯米克焊條		EZNiCu-1		Copper nickel, good machinability and bad crack resistance. Repair welding of sand hole and gray cast iron machined surface subject to no load. 鎳銅，易加工，但抗裂性較差。不受力的灰鑄鐵加工面及砂眼補焊					ENiCu-B
	Cu 107斯米克焊條		ECu		Red copper, atmosphere and sea water corrosion and excellent electric conductivity. Welding of red copper such as electrical copper row. 紫銅，耐大氣，海水腐蝕，導電性好。紫銅焊接用，如導電銅排					ECu
	Cu 207斯米克焊條		ECuSi		Silicon bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass. 硅青銅，耐蝕、強度高。銅、硅青銅及黃銅焊接用					ECuSi
	Cu 227斯米克焊條		ECuSnB		Tin phosphor bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass. 錫磷青銅，耐蝕、強度高。銅、硅青銅及黃銅焊接用					ECuSn-C
	Cu 237斯米克焊條		ECuAl		Aluminum bronze, wear and corrosion and high strength. Welding or surfacing of copper alloys. 鋁青銅，耐磨、耐蝕，強度高。銅合金焊接或堆焊用					ECuAl-A2
	Al 109斯米克焊條		TAl		Pure aluminum, excellent corrosion resistance and middle strength. Welding of pure aluminum. 純鋁，耐蝕性好，但強度不高，純鋁焊接用					E1100
	Al 209斯米克焊條		TAlSi		Silicon aluminum, good crack resistance and wide range of usage. Welding of aluminum alloys other than aluminum magnesium alloys. 鋁硅，抗裂性好，通用性大。鋁合金焊接用，不宜焊接鋁鎂合金					E4043
	Al 309斯米克焊條		TAMn		Manganese aluminum, corrosion resistance and high strength. Welding of aluminum alloys. 鋁錳，強度高，耐蝕。鋁合金焊接用					E3003
	Ni 102斯米克焊條		ENi-1		Pure nickel. Welding and surfacing of nickel and nickel to steel. 純鎳，用于鎳、鎳與鋼的焊接與堆焊					ENi-1
	Ni 207斯米克焊條		ENiCu-7		Copper nickel. Welding and surfacing of copper nickel and copper nickel to steel. 鎳銅，用于鎳銅、鎳銅與鋼的焊接與堆焊					ENiCu-7
Category 類別	Trade mark 牌號		Chemical comb 主要成份(%)		Characteristics & application 特性和用途					Equivalent to AWS 相當AWS
Hardfacing 硬面堆焊	S 101斯米克焊絲		C3 Cr28 Ni4 Si3.5 Fe Rem.		HRc48-54. Resistance to wear, gas corrosion and oxidation. Hardfacing of bucket tooth and case pump. HRc48-54，耐磨、耐氣蝕、抗氧化。堆焊鏟斗齒，泵套
	S 111斯米克焊絲		C1 Cr29 W5 Co Rem.		HRc38-47. Resistance to wear and corrosion at high-temperature. Hardfacing of high temperature and pressure valve. HRc38-47，高溫下耐磨、耐蝕。堆焊高溫高壓閥門					ECoCr-A
	S 112斯米克焊絲		C1.5 Cr29 W8 Co Rem.		HRc45-50. Resistance to wear and corrosion at high-temperature. Hardfacing of valve and hot-rolling pass. HRc45-50，高溫下耐磨、耐蝕。堆焊閥門，熱軋孔型					ECoCr-B
	S 113斯米克焊絲		C2.5 Cr30 W17 Co Rem.		HRc≥55. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of screw charging carriage. HRc≥55，高溫下耐磨、耐熱，但抗沖擊性差。堆焊螺旋送料機用
	S 114斯米克焊絲		C2.5 Cr30 W12 Co Rem.		HRc≥53. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of three-cone bit. HRc≥53，高溫下耐磨、耐熱，但抗沖擊較差。堆焊牙輪鉆頭					ECoCr-C
Copper alloys 銅合金	S 201斯米克焊絲		Sn1 Si0.3Mn0.3 Cu Rem.		Good mechanical properties and crack resistance. Gas welding and argon arc welding of red copper. 機械性能好，抗裂性好。紫銅氣焊及氬弧焊用					ERCu
	S 211斯米克焊絲		Si3 Mn1 Cu Rem.		Good mechanical properties. Argon arc welding of copper alloys and MIG brazing of steel. 機械性能好，銅合金氬弧焊及鋼的MIG釬焊用					ERCuSi-Al
	S 212斯米克焊絲		Sn5 Cu Rem.		Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。銅合金氬弧焊及鋼的堆焊用					ERCuSn-A
	S 213斯米克焊絲		Sn8 Cu Rem.		Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。銅合金氬弧焊及鋼的堆焊用					ERCuSn-C
	S 214斯米克焊絲		Al7.5 Cu Rem.		Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨、耐蝕。銅合金氬弧焊及鋼的堆焊用					ERCuAl-A1
	S 215斯米克焊絲		Al9 Cu Rem.		Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨、耐蝕。銅合金氬弧焊及鋼的堆焊用					ERCuAl-A2
	S 221斯米克焊絲		Cu60 Sn1 Si0.3 Zn Rem.		Melting point is about 890℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔點約890℃。黃銅氣焊及碳弧焊用，也可釬焊銅、鋼、鑄鐵
	S 221F斯米克焊絲		Cu60 Sn1 Si 0.3 Zn Rem.		S221 welding rod coated with flux. 外涂焊劑的S221焊絲
	S 222斯米克焊絲		Cu58Sn0.9Si0.1 Fe0.8 Zn Rem.		Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔點約880℃。黃銅氣焊及碳弧焊用，也可釬焊銅、鋼、鑄鐵					RBCuZn-C
	S 222F斯米克焊絲		Cu58Sn0.9Si0.1 Fe0.8 Zn Rem.		S222 welding rod coated with flux. 外涂焊劑的S222焊絲					RBCuZn-C
	S 223斯米克焊絲		Cu59 Sn0.6 Zn Rem.		Melting point is about 900℃. Braze welding of copper, steel and cast iron. 熔點約900℃。銅、鋼、鑄鐵釬焊用					RBCuZn-A
	S 224斯米克焊絲		Cu62 Si0.5 Zn Rem.		Melting point is about 905℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔點約905℃。黃銅氣焊及碳弧焊用，也可釬焊銅、鋼、鑄鐵
Copper alloys 銅合金	S 225斯米克焊絲		Cu48 Ni10 Zn Rem.		Melting point is about 935℃ and high strength. Braze welding of steel, nickel and carbide alloys. 熔點約935℃。高強度,釬焊鋼、鎳及硬質合金用					RBCuZn-D
	S 225F斯米克焊絲		Cu48 Ni10 Zn Rem.		S225 welding rod coated with flux. 外涂焊劑的S225焊絲					RBCuZn-D
	S 226斯米克焊絲		Cu60 Sn0.3 Si0.2 Zn Rem.		Melting point is about 900℃. Gas welding of brass, also braze welding of copper, steel and cast iron. 熔點約900℃。黃銅氣焊用，也可釬焊銅、鋼、鑄鐵
	S 227斯米克焊絲		Cu58Sn0.9Ni0.5 Si0.1 Fe0.8 Zn Rem.		Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔點880℃。黃銅氣焊及碳弧焊用，也可釬焊銅、鋼、鑄鐵					RBCuZn-B
	S 229斯米克焊絲		Cu55 Ni6 Mn4 Zn余		Melting point is about 920℃, high strength. Braze welding of steel, nickel and hard carbide. 熔點約920℃。高強度,釬焊鋼、鎳及硬質合金用
Aluminum alloys 鋁合金	S 301斯米克焊絲		Al≥99.5		Good ductility and corrosion resistance. Gas welding and argon arc welding of pure aluminum. 塑性好、耐蝕。純鋁氣焊、氬弧焊用					ER1100
	S 311斯米克焊絲		Si5 Al Rem.		Corrosion resistance, wide range of usage. Gas welding and argon arc welding of aluminum alloys other than high magnesium alloys. 抗裂性好，通用性大。鋁合金氣焊、氬弧焊用。不宜用高鎂合金					ER4043
	S 321斯米克焊絲		Mn1.3 Al Rem.		Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys. 良好的耐蝕性、可焊性及塑性。鋁合金氣焊、氬弧焊用
	S 331斯米克焊絲		Mg5 Mn0.4 Al Rem.		Corrosion resistance and high strength. Argon arc welding of aluminum alloys. 耐蝕，強度高。鋁合金氬弧焊用					ER5183

在線詢盤/留言

*您的姓名：

*聯系手機：

固定電話：

*聯系郵箱：

所在單位：

*需求數量：

*咨詢內容：

您要求給廠家提供：

免責聲明：以上所展示的信息由企業自行提供，內容的真實性、準確性和合法性由發布企業負責，本網對此不承擔任何保證責任。我們?cè)瓌t 上建議您選擇本網高級會員或VIP會員。

企業信息

天津赫伯特焊材科技有限公司

會員級別：試用會員

------------ 聯系方式 ------------

聯系人：劉秋菊（先生）

聯系電話：022-58614633

聯系手機：15122911331

傳真號碼：022-58558381

企業郵箱：768210656@qq.com

網址：

郵編：300230

進入商鋪

最新供應

推薦供應

人妻综合网,欧美一级二级三级视频,日韩精品无码波多野结衣,无码国产精品一区二区高潮